Filter By:

Workstands

Park Tool Truing Stand Upright Extension
$64.99
Park's Truing Stand Upright Extensions are made of durable chrome-plated steel and have quick-releases so they install in seconds to your Park TS-2 Professional Truing Stand (sold separately). The Uprights allow the stand to be used with wheels with hubs up to 160mm wide (found on some tandems and downhill bikes), and 29-inch mountain-bike wheels. Plus, there are specially sized bosses that act as adapters to hold wheels with 20mm through-axle hubs, too.
Park Tool Repair Kit for 100-3C and 100-5C Clamps
$45.99
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Park Tool PCS-EXT Extension Kit for PCS-1 Repair Stand
$44.99
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
Park Tool Portable Wheel Dishing Tool
$44.99
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Park Tool Work Tray
$43.99
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
Park Tool Floor Mounting Plate
$41.99
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
Park Tool Truing Stand Tilting Base
$35.99
The Tilting Base fits Park's TS-2 Professional Wheel Truing Stand (sold separately). It allows adjusting the truing stand 20 degrees forward or backward for comfortable use at any bench height. The handy front bins hold Park Spoke Wrenches (sold separately) and other small items such as nipples. Rounded bin corners make even the smallest parts easy to retrieve. The base's reinforced nylon body stands up to heavy use and has holes for mounting to a workbench for stability.
Park Tool Travel and Storage Bag for PRS-15
$31.99
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
Park Tool Travel and Storage Bag for PRS-20 and PRS-21
$30.99
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
Park Tool Replacement Clamp Covers
$14.99 - $28.99
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool Work Tray
$26.99
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
Park Tool Paper-Towel Holder
$16.99
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
Park Tool Tool Tray Collar
$16.99
Park Tool's Tool Tray Collar easily adapts the #106 Work Tray to fit the 41mm upright tube on 2011 and older PRS-20 and PRS-21 Repair Stands, as well as 1996 and newer PCS-1, PCS-4, PCS-4-1 and PCS-4-2 Repair Stands (each sold separately).
Park Tool Portable Workbench
Perfect for taking to races and rides, the Portable Workbench is a bench that folds for easy transport and storage. It features a large work surface with specially sized slots, holes, and recesses and for holding tools, shop towels, lubes, beverages, etc. The folding steel legs provide a solid base for a toolbox and supplies, too.
Previous page Page 2 of 2