Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Other

$9.99
- Prevents chain derailment when shifting to inner ring - Adjustable hose-type clamp fits 1-1/8" to 1-3/8" seat tubes
$15.00
Snap-on brake cable guides for bikes that don't have any. - Steel cable housing guide for 1-1/8" top tubes - Snaps on; no bolts - Set of 3 clamps
$30.00
- Includes stainless bolts - Fits 160mm front and 140mm rear rotors
$6.99
- Axle washers for use with 19mm bottom brackets - 19.1x26x2.0mm - Interface: 19mm - Sold in a 10-pack
$106.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 12mm - Outer Diameter: 24mm - Width: 6mm
$17.99 - $26.00
These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work. - Engineered and manufactured in Portland, Oregon USA - High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes - Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only - Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes - King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes - 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets - 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets
$5.00
- Aluminum straddle cable carrier for cantilever brake
$7.99
Heavy duty bolt-on aluminum seatpost clamp.
$17.99 - $20.00
Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g
$42.00 - $50.00
Dimension Steerer Extender adds 2 to 3-1/4" height to steerer. - Extender clamps to steerer; stem clamps to extender - Adds 2 to 3-1/4-inch height to threadless steerer - Includes top cap and long bolt - 40mm of threadless steerer is required for proper installation - Do not stack steerer extenders; no more than one steerer extender recommended per bike - WARNING: Dimension Steerer Extender is not recommended for use on forks with carbon fiber steerers
$24.99
- 7075 alloy construction with Cr-Mo bolt - Allows threadless stem use on threaded fork - Designed to work with 1-1/8" threadless stems - Converts a 1" threaded fork to 1-1/8" threadless - Provides 1" of additional height extension
$13.00
FSA bearings that set directly into the frame without the use of pressed in cups. - 36/45 degrees is Cane Creek-compatible - 45/45 degrees is Campagnolo-compatible
$14.99
This is an FSA MegaExo Crank Arm Bolt for 19mm MegaExo alloy cranks - Designed to fit alloy FSA cranks only - Includes M12 bolt, M27 self-extracting cap, and washers
$15.00
Replacement headset bearings from FSA. - Compatible with most Trek MTB integrated headset systems - Sealed bearing for long life - Compatible with Knock Block Headsets
$19.99
FSA Compression Plugs are top assemblies for carbon steerers. Replaces the traditional top cap assembly. Includes cap, bolt, and expander. - Includes cap, bolt and expander - Top assembly for carbon steerers replaces traditional top cap and star nut assembly
$30.00
Replacement headset bearings from FSA. - Compatible with most Trek MTB integrated headset systems - Sealed bearing for long life - Compatible with Knock Block Headsets
$8.00
- Color coordination, all the cool kids are doing it - Replacement lock rings for Giant Swage and Tactal Grips - 2 rings per package
$12.00
- Replacement V-brake pads - Wear limit mark - Ultra-light 6061-t6 forged pad holder - Compatible with Shimano, SRAM, TRP, and all major brands of V-brakes
$12.75
- Dust-proof and waterproof rubber seal cover. - Protect the power source connection on the frame when the e-bike is parked outside or when you carry it without the EnergyPak.
$13.00
-Seatpost clamp for Defy/Avail Advanced models (2015-2016)
$15.00
- Replacement pins for tool shed chain tool. - Bag of 10
$26.00
-Seatpost clamp for Defy/Avail models (2009-2016)
$26.00
-Seatpost clamp for TCR ADV/ADV SL models (2009-2016)
$30.50
Seatpost lever and cable set for Giant's Contact Switch Seatpost
$30.50
- Face plate spacer for Conduct brake. - Longer bolts included.
$40.00
Giant Contact S Type Bar Extensions fit the Giant Connect SL and Contact Clip-On Bar Clamps to provide you with an aerodynamic riding position for triathlon and time trials. Featuring lightweight alloy construction. Features - 22.2mm carbon aerobar extensions - Compatible with 45203-04 Clip-on Aerobar clamp
$40.00
Giant Contact Ski Type Bar Extensions fit the Giant Connect SL and Contact Clip-On Bar Clamps to provide you with an aerodynamic riding position for triathlon and time trials. Featuring lightweight alloy construction. Features - 22.2mm carbon aerobar extensions - Compatible with 45203-04 Clip-on Aerobar clamp
$53.00
- OD2 aero carbon Headset spacer kit for Contact SLR for Aero Integrated Handlebar
$63.00
Replacement cartridge for Contact Switch & Contact Switch S dropper posts. - Fits: Giant Contact Switch Post- Gen 1 (2018+)
Page 1 of 4 Next page